Magnetic field sensor

Magnetic field sensor
for pneumatic cylinders
BIM-NST-AP6X-V1131
■ Plastic, PA12-GF30
■ Magnetic-inductive sensor
■ DC 3-wire, 10…30 VDC
■ NO contact, PNP output
■ Male connector, M8 x 1
Wiring Diagram
BIM-NST-AP6X-V1131
4685800
Pass speed
Repeatability
Temperature drift
Hysteresis
Ambient temperature
ð 10 m/s
ï ± 0.1 mm
ð 0.1 mm
ð 1 mm
-25…+70 °C
Operating voltage
Residual ripple
DC rated operational current
No-load current I0
Residual current
Rated insulation voltage
Short-circuit protection
Voltage drop at Ie
Wire breakage / Reverse polarity protection
Output function
Switching frequency
10… 30VDC
ð 10 % Uss
ð 200 mA
ð 15 mA
ð 0.1 mA
ð 0.5 kV
yes/ cyclic
ð 1.8 V
yes/ complete
3-wire, NO contact, PNP
1 kHz
Construction
Dimensions
Housing material
Active area material
Electrical connection
Vibration resistance
Shock resistance
Protection class
MTTF
Mounting on the following profiles
Cylindrical design
rectangular, NST
28 x 17 x 14 mm
Plastic, PA12-GF30
Plastic, PA12-GF30
Flange connector, M8 x 1
55 Hz (1 mm)
30 g (11 ms)
IP67
2283 years acc. to SN 29500 (Ed. 99) 40 °C
.
NKLHI
Switching state
Included in delivery
LED yellow
1 x screw M3x20, 1 x tension bolt, 1 x spring washer
Functional principle
Magnetic field sensors are activated by magnetic fields and are especially suited for piston position detection in pneumatic cylinders.
Based on the fact that magnetic fields can
permeate non-magnetizable metals, it is possible to detect a permanent magnet attached
to the piston through the aluminium wall of the
cylinder.
Edition • 2016-09-21T18:36:53+02:00
Type designation
Ident no.
1/3
Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Edition • 2016-09-21T18:36:53+02:00
Magnetic field sensor
for pneumatic cylinders
BIM-NST-AP6X-V1131
2/3
Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Magnetic field sensor
for pneumatic cylinders
BIM-NST-AP6X-V1131
Accessories
Type code
Ident no.
Description
KLN 3 KLEMMSTÜCK
6970504
Mounting on K Dovetail groove cylinders or N T-groove
cylinders; clamping width 5.2…13.5 mm; material: Anodized
aluminium
KLN-SMC KLEMMSTÜCK 6970503
Mounting on K SMC cylinders; clamping width 4 mm; material: Anodized aluminium
KLF 1 KLEMMSTÜCK
6970401
Mounting on H external dovetail grooves; for all cylinder diameters, material: Anodized aluminium
KLF 2 KLEMMSTÜCK
6970402
Mounting on I external dovetail grooves (IMI Norgrem); for
Edition • 2016-09-21T18:36:53+02:00
all cylinder diameters, material: Anodized aluminium
3/3
Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com