magnetic field sensor for pneumatic cylinders

Transkript

ñEdition:
Hans Turck GmbH & Co.KG ñD-45472 Mülheim an der Ruhr ñWitzlebenstraße 7 ñTel. 0208 4952-0 ñFax 0208 4952-264 ñ[email protected] ñwww.turck.com
magnetic field sensor
for pneumatic cylinders
BIM-INT-AP6X-V1131
2.5
LED
6
0.3 m
28.8
32
5
●
rectangular, height 6mm
●
plastic, PA12
●
magnet-inductive sensor
●
3-wire DC, 10..0.30 VDC
●
normally open, pnp output
●
connector, M8 x 1
active face
Wiring diagram
M8x1
35
pnp
BIM-INT-AP6X-V1131
4623502
Pass speed
Hysteresis
Temperature drift
Repetition accuracy
Ambient temperature
ð 10 m/s
ð 1 mm
ð 0.1 mm
ï ± 0.1 mm
-25...+ 70 °C
Operating voltage
Residual ripple
10... 30 V DC
ð 10 % Uss
DC rated operational current
No-load current I0
ð 200 mA
ð 15 mA
Residual current
Switching frequency
Rated insulation voltage
Output function
Short-circuit protection
Voltage dip at Ie
ð 0.1 mA
ð 1 kHz
ð 0.5 kV
3-wire, normally open, pnp
yes / cyclic
ð 1.8 V
Wire breakage / reverse polarity protection
yes / complete
Housing style
Dimensions
Housing material
Material active area
Fixing screw tightening torque
Connection
cable quality
Cable cross section
Vibration resistance
Shock resistance
Protection degree
rectangular; INT
32x 5x 6mm
plastic, PA12
plastic, PA12
0.4 Nm
connector, M8 x 1
Ø 3, LifYY-11Y, PUR, 0.3 m
3 x 0.14 mm2
55 Hz (1 mm)
30g (11 ms)
IP67
Mounting on the following profiles
.
ENKF
Switch state display
LED yellow
+
3 BU

4 BK
4 BK
1 BN
3 BU
Function principle
Magnetic field sensors are actuated by magnetic fields and are especially suited for piston position detection in pneumatic
cylinders. Based on the fact that magnetic
fields can permeate non-magnetizable metals, it is possible to detect a permanent
magnet attached to the piston through the
aluminium wall of the cylinder.
ñEdition: • 22.03.2007
Type
Ident-No.
1 BN
ñEdition:
magnetic field sensor
for pneumatic cylinders
BIM-INT-AP6X-V1131
Accessories
Type code
KLZ1-INT
IdentNo.
6970410
Short text
Dimension drawing
mounting on F tie-rod cylinders; cylinder diameter:
32..0.40 mm; material: Aluminium; further mounting
accessories for other cylinder diameters on request
max. ø 7
40
KLDT-1
6913342
mounting on K dovetail groove cylinders; clamping
width: 10.5..0.120.4 mm; material: Aluminium; further
mounting accessories for other clamping widths on
request
7,5
26
10,5
2,5
9,6
20,3
KLR1
6970600
mounting to E round cylinders; material: Trogamid;
please order retaining straps separately
INT STOPPER
6900473
mounting on N T-groove cylinders; replacement without loss of switch-point with additional clamp INT
stopper; T-groove dimensions: 5..0.50.6 mm
6
12
ñEdition: • 22.03.2007
5